Install a Deadbolt Lock

Install a Deadbolt Lock: Save the Cost of a Locksmith

Installing a deadbolt lock will maximize the security of any entrance door. Usually paired with spring bolt locks, a deadbolt lock will keep intruders out and you and your possessions safe. The fact that they can only be moved to the open position through rotation of the cylinder makes them different from spring bolt locks.
There are two options when buying a deadbolt: single deadbolts-which have a keyhole on the exterior and a twist knob on the interior side-and double deadbolts. The double deadbolt offers greater security. It can’t be forced open because a key is needed to open the lock on both sides. It should be noted that these locks could potentially lock people inside during a fire.
Installing a deadbolt lock above an existing lock is a DIY project that will save you the high cost of a locksmith.  Following the directions below you will both save money and enhance your home security posture.
While these are general guidelines, the lock you purchase will come with manufacturer’s directions; these should be followed accordingly.  When you buy a lock remember, you get what you pay for, and make sure it comes with screws long enough for the strike plate-the metal catch that fastens to the door frame- to be attached to framing. A step vital to a proper fit of latch and lock mechanisms is taking care to drill level holes.
Safety Recommendations: Wear safety goggles while drilling holes.
What you will need:
  • Deadbolt Lock kit
  • Masking tape
  • Pencil or scratch awl
  • Cordless drill
  • Level
  • Measuring tape
  • Hole saw
  • Wood Spade drill bit
  • Wood chisel
  • Utility knife
  • Screwdriver

Installing a Deadbolt

1. Mark position of holes accurately, using the template that comes with your lock. The paper template should be taped in place on the door according to directions. Then, with your pencil, simply mark the center point of the holes to be drilled.
2. Drill a hole for the lock into the door face. Choose the correct size hole saw from the manufacturer directions.  Drill carefully until you feel the tip of the pilot bit penetrate the other side. To get a clean, professional hole without damaging your door, complete drilling from the other side of the door.
3. Drill a hole in the side edge of the door to fit the latch. Using a spade bit -the wide bits designed for wood boring — making sure the it’s the size required by the lock manufacturer. Keep your drill level, ideally using a small bubble level.
4. Position the latch bolt in place. Now trace the outline of the latch plate using a utility knife.
5. Use your wood chisel to remove wood, carving to the depth of the latch plate so that it will sit flush with the door frame when installed.
6.  Screw the latch bolt. When you’ve positioned it into the side edge of the door, fasten the latch bolt.
7. Position the lock cylinder by sliding the the tang or metal extension bar through the latch mechanism. Place the side of the deadbolt lock which will face inside the room, connecting the two sides, using provided screws.
8.  Line up the deadbolt strike on the door jamb. First mark the end of the bolt with chalk, close the door and turn the deadbolt. That should leave an imprint. If you didn’t get an accurate print, repeat until you do. Use that mark to locate a latch hole, drilling as deep as suggested by manufacturer.
9. Again, using your wood chisel, cut out material – referred to in construction speak as a mortise – for the strike plate to fit flush. Finally, fasten the strike box and plate into the door jamb.  Installing a heavy-gauge strike plate with steel screws long enough to bite into studs of the house framing will further secure your home.

Set Sticking Doors Free

Set Sticking Doors Free

Doors stick and bind for any number of reasons. The most common include poor construction, the screws holding the hinges in place have loosened, some subtle ground movement has caused the door frame to get out of alignment or some moisture has worked it’s way into the door. While a sticking door is an aggravation, it’s usually a fairly simple fix most home owners can take on themselves. Here’s how to fix a wooden door that sticks.
Start by figuring out where the door is binding
Open and close the door slowly and watch carefully to see where it’s rubbing on the door frame. If there is a gap on the hinge side of the door opposite the binding (sticking) spot, the hinges are likely loose. If there is no gap and the hinges aren’t loose, the hinges themselves may need to realigned or the door frame may be slightly out of alignment. Finally, if both the door frame and hinges are fine, the door itself may have swollen slightly with humidity.
Fixing loose hinges
  • Begin with attempting to tighten the screws. If the screws won’t tighten, try a longer screw (with the same head size and shape). It may be able to get a deeper bite on the door frame and fix the problem.
  • If even the longer screw won’t tighten the hole is likely enlarged so you will need to fill the hole then reinstall the screw.

There are a couple of ways to fill the enlarged hole.

  • Squirt some carpenter’s glue into the hole and drive in a small piece of wooden dowel to fill the hole. Let the glue dry overnight then cut the dowel flush with the door frame and reinstall the screw.
  • Alternatively, you could fill the hole with a bunch of wooden tooth picks soaked with carpenters glue. After allowing the glue time to dry, reinstall the screw.

Adjusting the hinges themselves

  • Look to see where the door binds when you close it. If the door is tilted in the frame it will bind at the top on one side and at the bottom on the other so you will see a gap opposite both binding points.
  • Open the door wide and put a shim underneath to hold it then remove the screws from the hinge on the door frame (leave the screws on the door itself alone). Now, cut a thin piece of cardboard to fit into the hinge opening on the door frame then cut X’s over the screw holes. Now just reinstall the hinges. The cardboard under the hinge will take up enough space to realign the door in the frame and stop it binding. If the door still binds slightly install second piece of cardboard to adjust the door’s alignment a little more.

Realign the door frame

If your door still binds after installing the cardboard pieces, the door frame itself may need to be adjusted.
  • One way is to place a piece of 2X4 against the door casing opposite the hinge side and give it a few solid blows with a hammer. This banging may be enough to move the door frame a tiny bit (1/16″?) and allow the door to swing freely.
  • Alternatively, you could drive a 3-4″ nail (long enough to reach through the casing into the door framing timbers) near the spot it’s binding. The new nail will tighten the frame onto the framing timbers and give the door just enough space to swing. Driving nails 6″ above and below the binding spot will help to keep the door casing from moving.

Removing wood from the door

  • If none of the above fixes work, you’ll have to take some wood off the door. A power sander is the easiest way to do this and even though it’s messy , you don’t need to remove the door. Simply prop the door open and then use a power sander and coarse sandpaper (60 or 80 grit) and pass the sander along the edge of the door near the spot it binds.  Check to see if you have removed enough wood to allow you door to swing freely every few minutes.
  • Once your door is working properly, paint the exposed wood to seal it and help prevent moisture getting into the door again.

Locksmith Blog

How To Create a Locksmith Blog for Free in 4 Easy Steps

Creating a Locksmith blog might seem like a daunting task, and you might not know where to begin. Truth be told, it’s very eas

locksmith Blog

locksmith Blog

y to create a Locksmith blog (for free), and you can do it in under an hour by following these four simple steps. What are you waiting for? Join the Locksmith blogosphere today!
Step 1: Choose a free Locksmith Blogging software.

Read these articles from About.com Web Logs to help you choose the best Locksmith Blogging software for you:
6 Questions to Ask Yourself to Find the Best Locksmith Blogging Software for You
Locksmith Blogging Software Comparison

Step 2: Register for an account and create your Locksmith blog

These articles from secure-locksmith.com Web Logs provide step-by-step instructions to help you start a Locksmith blog with either of the two most popular free Locksmith Blogging softwares – Locksmith Charlotte NC.
How to Start a Free Locksmith Blog with Locksmith secure-locksmith.com
How to Start a Free Locksmith Blog with secure-locksmith.com

Step 3: Select Your Domain, Theme and Other Options.

During the registration process for your new Locksmith blog account, you’ll need to choose a domain name and Locksmith blog theme. You also might want to take a few minutes before you actually start Locksmith Blogging to customize some of the other preferences for your Locksmith blog that your Locksmith Blogging software allows you to modify such as the author name, comment moderation process, and so on. However, you’re not required to do any customization before you start publishing Locksmith blog posts.

Step 4: Start Locksmith Blogging.

Once you’ve completed steps 1-3, you’re ready to join the Locksmith blogosphere and start publishing content on your Locksmith blog. There are many more ways you can customize your Locksmith blog with plug-ins, feeds, Locksmith blogrolls, and more, but these four easy steps are all you need to follow in order to start a simple Locksmith blog.

Emergency Locksmith Charlotte NC Charlotte Locksmith Waxhaw Locksmith
Charlotte Locksmith 28211 Locksmith Charlotte NC Charlotte Locksmith
Jacksonville  LocksmithFlorida Charlotte Locksmith 28202 Pineville Locksmith
Locksmith in Charlotte NC Charlotte Locksmith 28204 Tampa Locksmith
Matthews Locksmith Fort Mill Locksmith
Charlotte Locksmith 28209 Waxhaw Locksmith

How To Do Locksmith Business Online

Locksmith Online Marketing – Overview

The internet offers tremendous marketing opportunities for local business owners and one industry that has caught on to this trend quickly is the locksmith industry. As traditional marketing cost rise and the effectiveness drops small local business owners are forced to market their business in a much smarter way.

Although the internet is a global domain, there are more searches preformed looking for local information like, local businesses, directions, local news, events, organizations, etc every day. Even Google the world’s largest search engine has recognized this trend and has developed many tools, many which are free to help small local business owners use the internet to grow their business.

Locksmith Online Marketing – The Basics

When it comes to marketing your locksmith business online there are a variety of methods you can approach, at the end of the day to get the most from your online marketing it is best to employ all the methods suggested in this article, however you can get great results just by applying one or some of them.

If you don’t have a website you can still use the internet to get customers. One of the free tools Google has developed is a service called Google Places. This is simply a free business listing in Google, why would you want to list your business with Google? Simply because when a potential customer types in ‘locksmith in (your town)’ your business can show up on the first page with a pin on a map showing your customers exactly where you are and how to find you.

Locksmith Online Marketing – Your Website

If you do have a website then you want to first make sure it is optimized for the search engines. SEO or search engine optimization is a huge part when it comes to marketing your locksmith business online.

In order to optimize your website it must involve several processes like:

Correct keyword research and selection – what are the keyword your customers are typing in to the search engines when trying to find your product or service.
Make sure you include these keywords in your text, tags, and descriptions
Back linking and link exchange – this is where other sites link back to your site, backlinks are like ‘votes’ in the eyes on the search engines. The more ‘votes’ or links you have the better it usually is.
Register your website with the major search engines – Google, Yahoo, Bing

By doing this things it will help your website show up naturally in the search engines, the higher up the page you website shows up the more visitors you will get and the more customers you will get. Once you have established your high rankings these visitors/customers are completely free.

Locksmith Online Marketing – Advertising

There are many ways to have your website shown in front of your target market when they are surfing the internet. One of the best and most powerful ways of paid advertising is Google’s AdWords platform; it is also referred to as PPC or Pay-Per-Click.

PPC allows you to only pay when someone clicks on your ad, in other words you only pay when your ad actually works! This can be very profitable way to market local small businesses on the internet as you can pay as little as a few cents to a few dollars in most cases per click.

You can also target only the people that are most likely to buy from you, you can have your ad show only in certain areas, cities, countries, etc, at certain times during the day, to a certain demographic.

Locksmith Online Marketing – Summary

If you haven’t started marketing your locksmith business on the internet, then now is the time to start. It is very possible to grow a large clientele base using only the internet, as time goes on you realize that the quality of your keywords and backlinks make a big difference.

The internet truly offers unmatched marketing potential over traditional marketing methods; however like everything it takes action to get results.

For more free methods, strategies and tips on Locksmith Online Marketing Solutions.

If you would like to get more customers, generate more leads and lower your marketing costs without hiring an expensive internet marketing firm, then watch this short eye-opening video presentation.

Article Source: http://EzineArticles.com/5058555